its 11pm and my head is hurting - probably over thinking this..
when you have a three way mitre on boxing in ( so you end up with a shelf essentially.. )
how do you tile, having cut the trim?..as in, which surface first?
I feel it would be the top(shelf)?
then place the trim along that edge...
I am new to this forum and thinking to tile my bath floor on my own....
I have removed the toilet seat so I can put tiles underneath it.
Now any recommended way to make holes so I can screw the toilet seat.
I have just the manual tile cutter and Jigsaw with standard blade...
Now I am...
I'm not a tiler. Hope that's OK! We had a new kitchen, and the builder laid the porcelain tiles. After he'd finished (and we'd paid him), we saw the line by the living room door wasn't straight. He apologised, and offered to cut it straight with an angle grinder, but he can't get to the edges...
chris.hughes23
Thread
aus
cut
door
door frame
frame
how
how to tile
porcelain
porcelain tile
porcelain tiles
tile
tiles
tiling guide
usa
Had a tiler come round to give a quote for tiling my bathroom.
I have 60x60 porcelain to go on the floor and wanted them envelope cut into the wetroom tray.
The guy was very against the whole thing and said I should only really be using mosaic.
I've spent quite a few weeks reading these...
trusz
Thread
aus
cut
tanking
tile
tiles
tray
usa
waterproofing
wetroom
wetroom tiling
Hi, we have a bit of a problem, just installed a Climatech system in kitchen through to downstairs bathroom - we think the installation in the kitchen's fine as my boyfriend did it with my step-dad, then had to go to work so left step-dad to go through to bathroom. Unfortunately, he seems to...
Relayed a bathroom floor today after cracks started appearing in the tiles, the customer lost the details of the tiler that done it originally so could not call them back, He had laid hardi on top of floorboards and the cracks were appearing where the hardi boards joined after close inspection...
I'm soon about to tile my kitchen diner floor. I have a couple of questions...
Firstly, what sized notched trowel should be used for 600x300 porcelain tiles being laid on a concrete floor?
Secondly, the room has one challenging part, and that's a metal post that supports an overhead beam. It...
cutting tiles, say its 6inch one end, 7inch the other, pencil line, when I cut on my plasplug wet cutter, £30 job, it is quite hard to see the line with the brick coulered like water from the cutter, as im not cutting a straight line. is there a better cutter to place on a angle to cut? when it...
Just been watching this vid on the new Sigma kera cut tile cutter.... i like the last section where you can cut the tile into thin strips for curving around a column etc..
http://www.youtube.com/watch?v=dCBSXKdx6pk
DHTiling
Thread
aus
cutcutter
sigma
sigma cutter
tile
tile cutter
usa
what a joke, lost a bathroom re-fit that me and my plumber quoted, to a plumber that said he could do the plumbing and tiling alot cheaper, customer rang me today to ask if i could pop round and cut the boarders for the plumber there swan neck boarders and he cant mitre or cut them, he told her...
Was having a thought today, is there any reason why the dewalt, or any other wet saw for that matter, can't be used without water? Surely with the right blade it would be possible. I'm not planning on doing it, the dust would be mental! Just thout with winter coming up and the water in the wet...
Hello
I need to replace a shower mixer valve that will involve some new pipe work and fittings which in turn will involve removing a section of wall tiles so I can get to the pipes. What I would like to do is remove a section of tiles from ceiling to floor and about .5 metre wide then making...
Hi,
I'm having one end of my bathroom made into a wetroom, I have a retired professional tiler to do the job, unfortunately wetrooms were not in vogue when he was working, so he's are following the instruction leaflet.
Everything's gone well so far, the subfloor drain and the marine ply...
I have been trying to source a "shield" "double bent" tile for over a week now and it looks like I may have to find flat tiles to match age and color and then cut the "V" shape out of them.
I will probably have to do this by hand, any guidance on ensuring I don't spend longer picking up the...
I am replacing my blade from the standard blade which my cutter came with to hopefully a better quality blade. Could someone please reccomemed their favorite blade brand makes etc please?
Thanks, Toby
TobysTiling
Thread
aus
best
blade
cutcutter
dna
montolit
porcelain
tough
usa
wet
wet cutter
Hello, I need to cut a slight concave curve in some 1" 6x6 ruabon red tiles which I'm recycling!
I have angle grinders + diamond discs (105mm continuous and segmented rims)
Any advice gratefully received.
Thanks Neil