Not going to fail is it...

[Fliselege]

Started with a new firm last October, been on this job for 6 weeks now, walls weren't a problem, terrace another story. For starters they covered it in tarpauline and put diesel heaters in, but heat rises, toasty to work in but floor freezing, just carry on they said. Then found dip in floor, told bosses need to build up in self leveller, just carry on they said, use adhesive to build up, took this pic and showed one of the bosses, SLC delivered that afternoon....

 

[Bubblecraft]

Man, that's pretty high!

 

[Spud]

no drainage layer?

 

[Fliselege]

They're not fixed like that now, only laid them like that to prove my point to the pencil pushers, took them up and raised floor with SLC, now fixed properly

 

[Fliselege]

Cracking house, 5 levels built into rock face right on Oslo fjord, cruise liners dock 100m to the right, one of the weirdest sights I've ever seen, dirty great big ship floating past over next door neighbours roof top

 

[afright]

I would of layed them with a sand & cement bed.

 

[Diamond Pool Finishers]

Cracking house, 5 levels built into rock face right on Oslo fjord, cruise liners dock 100m to the right, one of the weirdest sights I've ever seen, dirty great big ship floating past over next door neighbours roof top
View attachment 48050View attachment 48051

Great looking place m8 !!,and it all turned out right in the end ,! i don't think the adhesive should ever be thicker than the tile !!

 

[jonnyc]

well i cant see the dip in the floor from photo and what with those new fandangled clips surely even with a slump there would be no lip and you would be very unlucky to turn the fall against what you laid tiles to.
its a different game in the country where you work now and assume from your good english narrative you do not hail from norway!
i think it is a very technical question as to whether the bed sinks in extreme temperatures or not.
It will depend on the product you are using I guess
sure, in cold climate it will take longer to cure but i have not been told that the tile will slump more in colder weather in uk using an adhesive formatted for the uk.
this brings up loads of questions.
in fact i had a scenario in 2004 where i laid a large area of french limestone inside a house with no heating or windows in place.it was january and freezing but because i had to do a job overseas at a fixed date i could not delay . i phoned adhesive tech line and they assured me that even though i fixed in under 5 degrees this was not a problem and the adhesive would go in to suspense mode!!
this was news to me but was assured that when the temperature raised the adhesive would cure.
so i left the job for few months
I had bedded stone in up to 10mm and i knew that under normal circumstance with the product i used it would not slump but adhesive manufacturer could not confirm what would happen.
as it turned out the floor did not slump/dried out fine and i have been cleaning and resealing it on a maintenace contract ever since.
but I think the question has to be is the adhesive you are using now in assumedly very cold temperatures up to the job you are being asked to do.
i am sure that adhesive manufacturers have a product to suit more extreme temperatures or they may tweak products we know to suit a certain climate .
i remember doing a couple of big jobs in southern sweden in january and it was certainly different than what we were used to. had to heat the sand up in morning just to use it.
heated loo seats in the site units were definitely a new experience !!
Whats it like over there on the tiling front. I have always been intrigued that the biggest jobs i was ever offered overseas were in Norway or alaska
I was offered to quote for four jobs over 1000mts and every one was high end limestone and reclaimed stone from paris ceramics.
at the time i was so busy in uk i turned the chance down as my guys didnt want to work in freezing weather and the jobs were always in winter.
I really wished i had tried to get one of them now just for the experience.
south sweden was fantastic.
carlos from limestone gallery had a monster job over there couple of years ago and unfortunately it was his undoing but he is rising again!
it was all oil men and they must just love stone after drilling through it to make their fortunes is all i can think.

 

[Fliselege]

well i cant see the dip in the floor from photo .

The tiles to the right row of 3 you can see are bedded nicely with a 10 mm notched trowel, then it dropped to what's in the photo...

 

[Fliselege]

From about where the white bucket is and all the way to the right of it had to be raised. My English is good because I'm London born and bred and there's shed loads of work here on the tiling front ;-)