New rotozip! - TilersForums.com

[Tiberius]

Hi all

Just got a rotozip rz3. Anyone else got one that has any tips on using it?

Cheers

Tib

 

[Deleted member 1779]

Hope it works out for you.

If you ever get stuck for a special size (for example installing an LED light that requires absoulte accuracy) then we supply a full range of core drills. 37 Diamond Drill sizes from 6mm to 125mm

Example of why accuracy is critical for installing some items

The main set is below:

And still represents excellent value for money at:

For the best selling kit

We also recommend using a wet sponge to control dust exposure, cool the drills and extend their lifespan.

And remember as a forum member you get discount too!

 

[Tiberius]

Hi

Thanks for your reply. I'll keep it in mind as I intend to get rid of my rubi set which was nearly £500 and whilst cuts fine,I find it hard to control along with the stand and resevoir full of water.

I guess the rotozip hasn't impressed too many as there's been no other replies!

Thanks again

Tib

 

[Stan001]

i've used the rotozip and actually liked it. I also have a set of those porsadrills which I put in my variable speed mains powered Bosch drill (it can go real slow) and like them too. Now the thing is this, the rotozip cost about a ton and the bits are quite expensive so for the same capability (for drilling holes) you can buy yourself a decent quality drill (which has loads of uses) and a set of porsadrills! Now the porsadrills probably wont last as long as the rotozip Bosch cores but the Porsadrill cores are cheap enough to amortise into a customers job and you can afford to have a set of common sizes! Now on the other side the Rotozip does have an excellent set of router type tools which used with the cheap looking handle attachment do a great job at routing things like board! ... so ... if your prime focus is drilling holes then Id go buy a nice drill (which has many more uses than the Rotozip) and bung some Porsadrill cores in it (especially if you can charge them every now and again to a job), but if you like the router capability then Id go for the Rotozip.
just my opinions.
p.s.
... and to throw you another curve ball - i got a tip-off that a well known orange and black shed sells their own make copy of a rotozip at half price, same size chuck etc (to take Bosch bits) which i have yet to check out.
p.p.s
... and the service from 365drills is excellent, i needed drills fast for a quick bathroom job, got them pretty much overnight by paying more on the postage, got a quick private email from them letting me know they were being packed (cos I pinged them to ask) so didnt have the worry of chasing them! that means a lot to me. 365drills understand customer service.

 

[Stan001]

... for tips on using it - get a load of scap tiles. You have to start the hole by going in on a 20% angle then straightening up then wiggling it around as you go through. (unlike the porsadrill which is a straight through using the template to stop you skidding when you start). I made a couple of snail marks when first using the rotozip but them could do it without skidding. (thats why i say get a load of scrap tile to practice). Another advantage you will find with your Rotozip is you can use them dry (you cant with the Porsadrills) which may be an advantage. For sure your zip will last forever, my drills are either Makita or Bosch, not had one blow on me yet. My variable speed drill is 20 years old and i use it for drilling at low speed through tile etc, and i also put a wisk on it and mix addy and grout. Its only a Bosch green so i should have killed it by now - but it doesnt even smoke (made in Switzerland!) ... bet you cant kill your zip either.

 

[gizzy2007]

i got the rotozip in aug last year and 2 of them has broke first the one of the cuttin blades snapped and jamed in the chuck and the second time the button at the side jammed in they just swapped it no probs and a like it too maybe am just unlucky

 

[kilty55]

i bought a 2nd hand rotozip off one of the lads on here,,i like it personally its been a good tool for profiling awkward cuts but thats all ive used it for so far...so far so good

 

[Tiberius]

Hi

I never got rid of the rubi drill bits in the end but did get some 365 bits.

They've been great so far, however, have been using them on travertine and slate, so we'll see how they fair next week on some genesis porcelain!

The 65mm bit came with a guide which was brilliant for accurately cutting out 8 spots. They rubis were never accurate enough unless I made a jig out of backerboard or plasterboard.

Top product!!

Thanks for the advice.....

Tib

 

[simmy08]

ive just thrown away my 2nd x core 6mm bit. came up against cermaiche keope full bodied porcelain's and lasted 10 cores. was not impressed as it does boldly state 100 holes. i have just bought myself the marcrist pg850 kit with 6mm bit. On the keope's it takes a very long time to get through, about 15 mins per hole and bottle and half of water. 5 bathrooms and they are all keope's so will see how it lasts.
Dont mind the waiting if the bits last a while.

I will continue to use the rotozip for ceramics only as it is worth its money for that alone and i will keep the marcrist for porcie's

have tried to adjust the water setting on the marcrist as i want a drip rather than a soaking but im at its lowest and there is still too much water for the small 6mm bit. Marcrist state that the water coming out around the core should be the colour of the tile, a little bit thick as to help the abrasion, thus resulting in extended life of bit and quicker cores

 

[Deleted member 1779]

ive just thrown away my 2nd (Rotozip) x core 6mm bit. came up against cermaiche keope full bodied porcelain's and lasted 10 cores. was not impressed as it does boldly state 100 holes.

Have you tried the PORSASRILL 6mm diamond core drills?

A pack of four 6mm-drills retails at £29.99 (dont forget as a Tilers Forum Member you get your discount on top of that )

To use them we suggest holding a wet sponge on them.

365Drills in action using the 6mm core drills.

The PORSADRILL system removes a CORE from the tile.

have tried to adjust the water setting on the marcrist as i want a drip rather than a soaking but im at its lowest and there is still too much water for the small 6mm bit.

With the PORSASRILL 6mm kit a sponge soaked in water eliminates dust exposure for the installer and increases the lifespan of the holesaw by cooling the drilling operation which in turn leads to faster drilling. Our own sponge is ideal because it is the correct size and shape so it will not obstruct your drilling. It retains a superior amount of water. And having a dedicated drilling sponge saves the hassle of using your tile grouting sponge and contaminating it with grit, dirt and diamonds. A great aid at a reasonable price.