HI guys and galls.
I have recently extended and plasterboarded (vapour barrier type - silver backing type which is what building control specified) my bathroom. I am about to install the bath which will run down one wall only i.e. not into a corner of the room. I have read many things on here...
hello all.just after a bit of advice about finishing a tiled bath panel.do you finish the panel flush with the front of the bath or do you come up under the top rim of the bath or, is every bath different? thanks in advance, dave.
Looking for a bit of proffesional advice, I need to tile a bath panel, standard size bath. Would 9mm or 12mm ply be ok ? also is a standard tile adhesive ok on the ply if ply is to be used ? thanks in advance. :thumbsup:
one of my guys has droppeda tile on edge of bath yesterday.
anyone know of a good repair compNY IN SOUTH EAST ENGLAND for this type of repair .
is it possible to make a perfectly invisible repair.
bath is betteocean enamel code 8857-000
Hi,
Am on the final straight of my wetroom project!
The wetroom is fairly small (2.5x2.0m) and there is a bath fairly close to the shower area, so I am expecting the bath is going to be splashed by water when taking a shower.
I want to fit glass panels to the side and end of the bath and...
ojtiler
Thread
aus
bathbath panel
frame
glass
metal
panel
tanking
usa
waterproofing
wetroom
wetroom tiling
Hi, this is my first post so first of all just like to say a big thanks to all for as I have picked up lots of know how from reading the various posts. Sadly I feel a little sick right now after dropping my trowel which somersaulted in slow motion and took a small chip out of my bath. its about...
How do I drill a hole in a cast iron bath?
Dear 365-Drills, We are a contractor converting a National Lottery Heritage site and it contains this very heavy Drummonds Lomond cast iron bath that is difficult to move about...
Deleted member 1779
Thread
aus
bath
drill
find a tiler
hole
how
job
jobs
tiling job
tiling jobs
tiling work
usa
work
Hi,
here is my first post, and I am looking for some advice.
We had a bathroom refit a fair few years ago, but now it's looking a bit tired, so I want to rejuvenate it.
There is a shelf built at the tap end of the bath, but it sits flush with the bath, it's had some water ingress as all the...
What adhesive would you use to tile a bath panel? proborbly 9mm ply
I have used no more nails in the past with flexi grout and that seemed to be pretty good...what would you use?
Martino
Thread
adhesive
aus
bathbath panel
panel
tile adhesive
tiled
usa
Using manilla silicone on the external joints but should i use white around the bath, back of sink and the toilet?
the batroom suite is white ...tiles are beige.
What do you guys do?
Hi guys,
I need a quote from a good tiler in the Bath area. I have 13 sq mtrs of Honed Travertine floor tiles which need to be layed in my kitchen over UFH, (cabled not on a mat) on 20mm ply. Which i will lay myself
Questions; Is it wrong for me to purchase the adhesive first, or best left to...
Hello All :)
I have a bath to be plumbed in & tiled around (I have constructed a frame, timber & aqua panel, to support tiles and bath), I want the tiles to sit just under the rim of the bath so you cant see the cuts. The tiles will be around 3 edges of the bath, a tiled shelf along one side...
Hi All.
Recently started ltd company doing Tile and Tadelakt. I want to concentrate on Tadelakt and there is a good possibility that I may need to sub some of stone fixing out. I had a marble mason who I was hoping to use, but this has fallen through. If there's anyone in here who would be...
I primed my walls and then put the tiles on over a week ago but the adhesive was still not fully dried out by last night, I have ended up taking the tiles off again:thumbsdown: I now need to replace some of the plasterboard, and would like any tips on wot is going wrong Any Ideas???
I'm currently completing my first ever attempt at tiling. I've got a gap of 38mm between the end of the bath and the tiled wall. Can anyone suggest how I should complete this part of the job. Thanks
Hi all, when fitting Marmox boards around a shower bath is it best to get the bath in situ and board up the to the bath or board the entire wall and then put the bath in after. Does it not make too much difference either way (apart from saving some board if you go down the first route)? Thanks
siremastimus
Thread
backerboard
bath
boards
marmox
marmox backerboard
shower
tile backerboard
usa
Hi Forum Members,
I have one more newbie question before finishing off my first ever tiling job. This time about boxing in. Our bath does not meet the wall at the non-business end (it's about 15cm between the wall and the bath). What we're thinking of doing is:
Building a wooden frame (the...
Tiling a bathroom floor next week. Customer has a roll top bath that is goin on top of Ceramic tiles. I've looked at the bath and my concern is that the feet appear to have quite sharp contact point that will be on the tiles. Would some sort of barrier reccomended(rubber washer or sliver of...
Good evening all. :thumbsup:
My next project involves tiling around a bath with a shower within a 7 year old apartment. When removing the previous tiles and walls i found hardibacker board at the shower end of the bath and double skin plasterboard on metal studs at the other ends.
My initial...