UK Tiling Forum; Established 2006
Welcome to the UK Tiling Forum by TilersForums.com, built in 2006 by Tilers, run by Tilers.
View all of the UK tiling forum threads, questions and discussions here.
Tilers Forums Official Sponsors
C
charlie1
I remember when I started tiling, ohh well over a year ago now, I used to use a manual saw to cut out the bottom of the door facings, those where the day's. I now use a fein.
No seriously that is very interesting, I would like to hear about more of the old way's.
Wait till pjtiler wakes up and we will hear all about them.
Good post
No seriously that is very interesting, I would like to hear about more of the old way's.
Wait till pjtiler wakes up and we will hear all about them.
Good post
Last edited by a moderator:
G
Gazzer
Ah the old days, happy days.
Most floor tiling back then was Quarry floors, Dennis Ruabon, Platts, Wooliscroft type stuff. Sawdust was used mixed with water to dampen it and then after we grouted with sand and cement, the sawdust spread over the floor to clean off. When the tiles were clean dry sawdust was spread over and that polished off. you had to do it right otherwise the sawdust would stick in the joints.
Tiles came with nibs on the edges called self spacers, then the changed to universal tiles with a bevelled edge to act as a self spacer, 2 edges would be glazed. This would do away with having to have Re`s ( round edge). There used to be Rex ( round edge external) for corners and lots of others.
When fixing skirting tiles you would have "sit ins" or Sit ons" and internal/external angles.
Tiles were cut with small hand scribers ( still available) and everyone would have a cutting board in the van. This was a board with an upstanding edge, like another strip of would screwed at the edge. This would enable you to cut all tiles to the correct size .
Quarry tiles were cut with small hammer and small cutting chisel, freehand!!! then the tile was tapped from the back to break down the line.....yeah missed plenty of times and hit my fingers:furious3:.
Floor tiling was done by laying a sand and cement screed and a slurry of cement poured onto the floor and then tiles tapped into the bed. We could screed far better in those days than the screeds i see now.
Squeegees (grout tools) were hand made with old rubber tiles that you could find back then, or rubber strips sandwiched between 2 pieces of architrave. Sponges were salvaged from old 3 piece suites.
oh yeah and every apprentice knew every chip shop in every town :lol:
Most floor tiling back then was Quarry floors, Dennis Ruabon, Platts, Wooliscroft type stuff. Sawdust was used mixed with water to dampen it and then after we grouted with sand and cement, the sawdust spread over the floor to clean off. When the tiles were clean dry sawdust was spread over and that polished off. you had to do it right otherwise the sawdust would stick in the joints.
Tiles came with nibs on the edges called self spacers, then the changed to universal tiles with a bevelled edge to act as a self spacer, 2 edges would be glazed. This would do away with having to have Re`s ( round edge). There used to be Rex ( round edge external) for corners and lots of others.
When fixing skirting tiles you would have "sit ins" or Sit ons" and internal/external angles.
Tiles were cut with small hand scribers ( still available) and everyone would have a cutting board in the van. This was a board with an upstanding edge, like another strip of would screwed at the edge. This would enable you to cut all tiles to the correct size .
Quarry tiles were cut with small hammer and small cutting chisel, freehand!!! then the tile was tapped from the back to break down the line.....yeah missed plenty of times and hit my fingers:furious3:.
Floor tiling was done by laying a sand and cement screed and a slurry of cement poured onto the floor and then tiles tapped into the bed. We could screed far better in those days than the screeds i see now
.Squeegees (grout tools) were hand made with old rubber tiles that you could find back then, or rubber strips sandwiched between 2 pieces of architrave. Sponges were salvaged from old 3 piece suites.
oh yeah and every apprentice knew every chip shop in every town :lol:
Last edited by a moderator:
T
The D
I can tell form that you were there. One of the things my uncle taught me was in the sawdust instead of water if you put raw linseed oil when you spread the sawdust on the floor and rubbed it in to the tile it would levee them looking mint. This was on quarry tiles glazed tiles as you say just put water in the sawdust. Grouting was don using a wet slurry of sand and cement and brushing it in to the joints then get a semi dry mix and sprinkle it all over the floor when you rub it of the joints are full and the tile is totally clean.
Last edited by a moderator:
T
The D
Back in the day there was not any of this newfangled tile trim there were bull nose tiles glazed edge tiles or you had to mitre the edge of the tile using your tile nippers and a rubbing block oh how I miss them days. (Not)
Last edited by a moderator:
T
The D
I will bet a lot of you new tilers don’t know the origins of BAL but BAL was set up by H&R Johnson’s to develop new adhesives for the new backgrounds that were being used such as gypsum plaster and plasterboard. The trend was changing from tilers fixing straight in to sand and cement screed and render to fixing on to the sub-straight after it had cured. There are a few reasons for this one was dry lining and the over whelming demand for cheaper materials and fixing methods.
Last edited by a moderator:
P
Pawelzik
"Is the screed still too wet for tiling" was tested by laying a newspaper on the screed with a brick on it. After a waiting time of 1 night resp. 24 hours the newspaper was looked at if it is wet = screed contains still too much moisture.
S
Spirit
The carts were, but had trouble getting the paint to stick to the horse
D
DHTiling
Having to soak your wall tiles in a tub before you could fix them with sand&cement mix to get a good hold or the tiles soaked the moisture from the cement bed and fell off again...🙂🙂.....
P
pjtiler
when me and Michael Angelo tiled the Sistine chapel in Rome we had to make our own Mosaic from broken plates and Potts found in the local potters skip
P
pjtiler
quarrys use to arrive on site loose on flat back trucks
which took all morning to unload and cut your hands to ribbons
which took all morning to unload and cut your hands to ribbons
P
pjtiler
tilers don't know there born these days
when i started i had to get up 2 hours before i went to bed work a 29 hour day on my knees being whipped by the Foreman every 10 minutes
i,d stagger back to the cardboard box which was home to the 25 of us have a lick of my dads razor strop for my tea then sleep on the cold cobbles with a crisp bag as a blanket for 5 minute before another day work
and i had to pay the boss 1/6 a week for the privilege
eeeeeeeeeeeeeeeeeee but we were appy
when i started i had to get up 2 hours before i went to bed work a 29 hour day on my knees being whipped by the Foreman every 10 minutes
i,d stagger back to the cardboard box which was home to the 25 of us have a lick of my dads razor strop for my tea then sleep on the cold cobbles with a crisp bag as a blanket for 5 minute before another day work
and i had to pay the boss 1/6 a week for the privilege
eeeeeeeeeeeeeeeeeee but we were appy
G
Gazzer
Was it Hawkins Quarry tiles that were made as a pair? So when they arrived you had to split the apart with a big flat screwdriver...those were piggin sharp:furious3:
The days when a mixer was either powered by diesel and used to mix sand and cement screed or a mixer was a piece of steel conduit used to mix CTF with .
The days when Hard hats were best used to carry nails across site.
The days when you had to go to the timber yard to get 20p bags of sawdust.
The days when all floors were level........cos you had to screed them.
The days when you piled into the back of a J4 Commer van and fought over a bucket to sit on for the journey home.
Yes happy days
The days when a mixer was either powered by diesel and used to mix sand and cement screed or a mixer was a piece of steel conduit used to mix CTF with .
The days when Hard hats were best used to carry nails across site.
The days when you had to go to the timber yard to get 20p bags of sawdust.
The days when all floors were level........cos you had to screed them.
The days when you piled into the back of a J4 Commer van and fought over a bucket to sit on for the journey home.
Yes happy days
P
pjtiler
pancake Tuesday
the day all the apprentices were initiated (if they could find you )
i had my bolloxs blackened with plumbers black (its a kind of lead paint ) and hung upside down from the tower crane 60 ft up at duttons brewery blackburn
the up side was we could all go home at 12
the day all the apprentices were initiated (if they could find you )
i had my bolloxs blackened with plumbers black (its a kind of lead paint ) and hung upside down from the tower crane 60 ft up at duttons brewery blackburn
the up side was we could all go home at 12
P
pjtiler
conways had bedford vans with sliding doors if you had to brake hard they would take your arm offWas it Hawkins Quarry tiles that were made as a pair? So when they arrived you had to split the apart with a big flat screwdriver...those were piggin sharp:furious3:
The days when a mixer was either powered by diesel and used to mix sand and cement screed or a mixer was a piece of steel conduit used to mix CTF with .
The days when Hard hats were best used to carry nails across site.
The days when you had to go to the timber yard to get 20p bags of sawdust.
The days when all floors were level........cos you had to screed them.
The days when you piled into the back of a J4 Commer van and fought over a bucket to sit on for the journey home.
Yes happy days
T
The D
And you had it good.:lol:
T
The D
Did you boys ever use rope for spacing those fat old frost proof tiles for shop fronts and columns?
P
pjtiler
shaws twin tiles ??
we used a semi dry mix and tapped them in
T
Taz8130
This still goes on...........when applying for a business bank account when you first start up !!!!
Last edited by a moderator:
W
White Room
When I started work, To make a hole in a brickwall to fix somethink cannot remember what it was called, Had to hammer this "thing" turn it as you hammered to make a hole then wall plug. That was hard work, Next to no drills and certainly no cordless. That was back in 1971
D
DHTiling
S
Spirit
That is a Rawl Drill, still have one in my toolbox. It is never used for masonry drilling but has 1001 other uses.
No, not a plugging chisel. This thing has a point and 3 cutting edges (crap description)
Cannot find a picture of it, might have to get my camera out tomorrow.
No, not a plugging chisel. This thing has a point and 3 cutting edges (crap description)
Cannot find a picture of it, might have to get my camera out tomorrow.
Last edited by a moderator:
T
Taz8130
When I used to work with my Grand-Dad he used one as well, I think it was called a "Plugging Chisel"
W
White Room
D
DHTiling
that is a plugging chisel as well..lol lol lol....
Roughneck Plugging Chisel 10.5" - Screwfix.com, Where the Trade Buys
W
White Room
Spirit got the description right, a point and three cutting edges, God that takes me back:yes:
S
Spirit
The plugging chisel predated the rawldrill.
The plugging chisel was used to make a larger hole that was plugged with a tapered piece of wood.
https://www.tilersforums.com/attachments/rawlplugs_get_a_grip_history_of_rawlplug-pdf.136933/
The Rawldrill is pictured at the end of the article.
The plugging chisel was used to make a larger hole that was plugged with a tapered piece of wood.
https://www.tilersforums.com/attachments/rawlplugs_get_a_grip_history_of_rawlplug-pdf.136933/
The Rawldrill is pictured at the end of the article.
D
DHTiling
even before my time.......give me a drill please......:lol:
There are similar tiling threads here
Featured Threads
-
- F
- W
-
- I
-
-
-
