Mezzanine floor prep

[goz]

Good morning gents , been asked to price a 300m mezzanine floor in a showroom .
38mm chipboard. They have indicated that it will be well supported etc, how would you go about prepping?
Ditra or overboard with hardie or Wedi. Expansion joints obviously.
The building has not been built yet, they are getting prices together.
This is all on the understanding that there is sufficient support in the floor of course

 

[Dumbo]

Quick question . Do you know why they are using 38 mm chip , is it subject to heavy loading .

 

[Qwerty]

Interesting project. Personally I would get all the specs and details together and then approach an adhesive company such as @ISOMAT UK who could give you a full method statement

 

[goz]

Quick question . Do you know why they are using 38 mm chip , is it subject to heavy loading .

It’s a motorcycle showroom, they will have them on the mezzanine aswell as the ground floor so a bit of weight, which makes the prep all the more important.
If it’s a new build surely be better to have a concrete mezzanine?

 

[WetSaw]

We used steel framed mezzanine floors in the motorcycle warehouses I used to work in. As they were only leased it was cheaper and easier to install a steel structure then board it. We just had a company come and measure, manufacture then we put them up.
Never tiled them so rather useless information really!

 

[Bill]

300m mezzanine........ that is some floorspace.

A few problems with the 38mm chipboard for tiling onto.

1, They are using 38mm so that they can have fewer supports (joists, noggins etc) which doesn't help tiling.

2, Covering all that in Hardie will probably lose you the contract, cost wise.

3, Movement will be a big factor and I am not sure even the best crack mat & movement joints will stop the floor from cracking (eventually)

Do the clients understand the difficulties in tiling onto such a structure?

 

[goz]

300m mezzanine........ that is some floorspace.

A few problems with the 38mm chipboard for tiling onto.

1, They are using 38mm so that they can have fewer supports (joists, noggins etc) which doesn't help tiling.

2, Covering all that in Hardie will probably lose you the contract, cost wise.

3, Movement will be a big factor and I am not sure even the best crack mat & movement joints will stop the floor from cracking (eventually)

Do the clients understand the difficulties in tiling onto such a structure?

There’s the option of laying karndean or the like on the mezzanine, still 350m2 on the ground floor to tile do not too fussed if they don’t tile the first floor. My spider sense tingled so I thought I would put up the bat signal on here .

 

[LM]

Advise them to go with LVT imo. To do that correctly in hard tiles would cost way too much in time and money.

 

[Glynn]

Advise them to go with LVT imo. To do that correctly in hard tiles would cost way too much in time and money.

Is that good advice on a tiling forum? We will soon be out of work.

 

[LM]

Is that good advice on a tiling forum? We will soon be out of work.

To answer your question yes imo!
The way I see it is that if the substrate has so many things going against it for tiling and money is an issue, the potential cost of getting it properly ready may mean somebody deciding to take a chance with preparation and a failure could happen. So unless of course they’re prepared to spend whatever is necessary to prepare it properly then I do think it’s better not to tile it.
Sometimes builders/owners will take a chance and tell you not to worry they know the gamble they’re taking and to do the best you can with it. That’s all fine until it goes wrong and then the tiler is to blame no matter what because he should have knew better. You’ll soon be out of work if that happens because your reputation will be trashed.
Of course you’d want to tile it if it’s been spect up and all the proper prep was carried out.