Travertine edging

[bigmal]

Hi guys
Hope you don't mind a DIY type invading your very professional forum!

Done various jobs over the years for myself and mates, and always been pleased with the results. Only use a cheapo electric wet cutter, but seems to do the job.

In process of rennovating bathroom - plaster was dodgy, so that's all off. Plan to fix HardiBacker to timber studs, but a mate is going to replaster one internal (brick) wall traditionally.

I would like to step up a notch and go for Travertine... so my question is about the cut edges, eg the return into the window recess. I would normally use plastic/metal edging trim, but I'm guessing this would ruin the effect of the Travertine. What do you pro's do? Leave a bare edge (perhaps sanded???) and just overlap the corner joint?

Any advice gratefully accepted!

Thanks

Big Mal

 

[Dan]

Welcome to tilersforums.com | Tile Forums | Tiling Forum!

Hello bigmal, welcome aboard www.tilersforums.com. Stick around, I'm sure you'll like the place.

 

[Deleted member 9966]

:welcome: bigmal

DIYer's are always welcome. that how I found my way here

 

[faithhealer]

Welcome big mal, have a look at this, it tells you that you might have to reconsider plastering that wall. Tiles and Adhesive Weight Per Square Metre - THE TILE SOURCE

 

[bfast tiler]

it is always more authentic when the travertine is overlapped and a gap left to coincide with the same size as the joint size...normally 3mm put the cut edge into the window reveal & clean edge exposed.

 

[Time's Ran Out]

it is always more authentic when the travertine is overlapped and a gap left to coincide with the same size as the joint size...normally 3mm put the cut edge into the window reveal & clean edge exposed.

This edge always looks a professional finish if you round,fill and polish it.
:welcome:

 

[Diamond Pool Finishers]

hi:welcome: to the forum

 

[bfast tiler]

This edge always looks a professional finish if you round,fill and polish it.
:welcome:

that is the way i would do it t.j i was offering a d.i.y-er a d.i.y approach there is a bit of experience needed to polish.......and b&q dont do the disc's for soft stone if its a clean edge then a sealer will also give an almost desired affect.

 

[DHTiling]

Hello and welcome...

You can finish the edges with various grit sanding pads to a nice enough result and slight chamfer to remove the sharp arras edge.

But if you like you can also buy some diamond hand pads designed just for this type of edge finishing.

Montolit Diamond pad set


Diamond hand pads for smoothing the edges of any type of:

- Marble
- Granite
- Porcelain
- Stoneware
- Ceramics

Blue = Medium grit
Red = Fine grit

Can be used wet or dry

Tradetiler tilers Files & Rubbing Blocks


I like to try and gett he edges as close a finish tot eh tile surface be it honed or polished and if customer requires it then i also bull nose the edge but for a DIY job then those hand pads will make light work.

 

[merlecollins]

If you really want a bullnosed edge, you could cut the tiles to size and take them to a local marbleworks - They'd have the relevant tools to stick a bullnose on for you or even a headstone maker:yikes:

 

[bigmal]

Thanks everyone for excellent advice so far!

I might have to rethink based on the weight... but the Travertine really does look the dog's wotsits - and is a pretty good price compared to many "manmades'

cheers

 

[doug boardley]

Hi Mal, if you're going down the traditional plaster route on one wall, use sand and cement render and leave it unskimmed. Don't let your plasterer use a gypsum basecoat as this is unsuitable to tile onto. Another solution would be to dot and dab 12.5mm plasterboard on your wall (I'm assuming it's a masonry wall), and again, leave unskimmed

 

[mikethetile]

:welcome:good luck with thee job, you will get sound advice on here

 

[suave]

:welcome:

 

[diamondtiling]

Welcome to the forum.

 

[david campbell]

:welcome:to the forum

 

[White Room]

Hi and welcome

 

[Ken Bruty]

:welcome:

 

[Daz]

Hi & welcome.

As Dave says, the Montolit pads are a great way of finishing the edges without a great deal of expense.

 

[Scott]

:welcome:

 

[The Legend; Phil Hobson RIP]

:welcome: