Currently reading:
Check me out!
Discuss Check me out! in the Australia Tiling Forum area at TilersForums.com.
Diggy
TF
D
David Rowell
I was feeling a bit brave today and decided to try out my new circular saw, I'm now a fully fledged multi trader!
Tomorrow I'm going to butcher a plinth
To save you the trouble of using clamps and spirit levels and subtracting measurements. There a simple jig you can make.
Get a piece of 6 mm ply of you desired length glue and pin a straight piece of lathe to it. Make sure the width of the ply is greater than your saw. Put saw fence against the lathe and cut straight through the ply. Now the next time you cut simply put the ply edge against your cut line with confidence it will cut it bang on. Pictures on request if ya fancy making one
S
Stef
To save you the trouble of using clamps and spirit levels and subtracting measurements. There a simple jig you can make.
Get a piece of 6 mm ply of you desired length glue and pin a straight piece of lathe to it. Make sure the width of the ply is greater than your saw. Put saw fence against the lathe and cut straight through the ply. Now the next time you cut simply put the ply edge against your cut line with confidence it will cut it bang on. Pictures on request if ya fancy making one
That's a great bit of advice, cheers.
I do the exact same as Bri has done in the photo.
I'm not a multi-trader though. [emoji1][emoji1]
D
David Rowell
I was feeling a bit brave today and decided to try out my new circular saw, I'm now a fully fledged multi trader!
Tomorrow I'm going to butcher a plinth
To save you the trouble of using clamps and spirit levels and subtracting measurements. There a simple jig you can make.
Get a piece of 6 mm ply of you desired length glue and pin a straight piece of lathe to it. Make sure the width of the ply is greater than your saw for extra stability add draught excluder tape to bottom. Put saw fence against the lathe and cut straight through the ply. Now the next time you cut simply put the ply edge against your cut line with confidence it will cut it bang on. Pictures on request if ya fancy making one
D
David Rowell
Ive got a festool plunge saw now but that set me back nearly 600 quid with the tracks but worth every penny. The system i described was how i used to do it. My festool is like the sigma or rubi of tile cutters
D
David Rowell
Ive got a festool plunge saw now but that set me back nearly 600 quid with the tracks but worth every penny. The system i described was how i used to do it. My festool is like the sigma or rubi of tile cutters
To save you the trouble of using clamps and spirit levels and subtracting measurements. There a simple jig you can make.
Get a piece of 6 mm ply of you desired length glue and pin a straight piece of lathe to it. Make sure the width of the ply is greater than your saw for extra stability add draught excluder tape to bottom. Put saw fence against the lathe and cut straight through the ply. Now the next time you cut simply put the ply edge against your cut line with confidence it will cut it bang on. Pictures on request if ya fancy making one
Are you a chippy by trade david..?
D
David Rowell
One the best tools in my van !
i hardly ever use my planer anymore really. When im fitting doors this is the beast i use. Back bevel of 3 degrees job done. I ise a makita or freud blade for it works a treat
D
David Rowell
Yes mate my business is called DWR Joinery. Just took a real liking to tiling lol
S
Stef
Why? Because you can't cut plinths! [emoji23]
D
David Rowell
Or plaster. .:sofahide:...lol
I had to refit a toilet in my mates house the other day after tiling his floors, had to cut pipes use tighten up thingies to tighten up stuff and push stuff on , not one leak, I'm a bloody plumber now [emoji33][emoji106][emoji41]
D
David Rowell
score your lines with a nice sharp stanley to retain the crisp edge works really well and prevents tear out
Or tile [emoji33]
S
Stef
Plumbings a doddle Craig, it's as easy as putting nuts in a monkeys mouth.. [emoji6]
I
Ian
I plugged my radio in today....im now a sparky..
Woah!!!! Steady on, you can't do anything until you've done that weekend course my friend [emoji23]
L
lizzardtong
More likely coal miner
C
Concrete guy
One the best tools in my van !
We make diamond blades that fit the TS55 Festool, we currently have three types that fit depending on what you're cutting.
Currently
Granite
Quartz
Porcelain/Ceramic
These were produced to request for a number of large customers we have to solve particular problems they were having cutting their materials.
Reply to Check me out! in the Australia Tiling Forum area at TilersForums.com
Posting a tiling question to the forum? Post in Tilers' Talk if you are unsure which forum to post in. We'll move it if there's a more suitable forum.