You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
square
Search the forum,
In Euclidean geometry, a square is a regular quadrilateral, which means that it has four equal sides and four equal angles (90-degree angles, π/2 radian angles, or right angles). It can also be defined as a rectangle in which two adjacent sides have equal length. A square with vertices ABCD would be denoted
Hi
i found out on friday that the dewalt dw060k - Tile laser square is being discontinued by dewalt..
there is not many left, so if you have been thinking about buying a laser square for floor tiling/setting out, then dont hang about too long..
heres the one ...
Aston
Thread
dewalt
discontinued
floor
floor tiling
laser
square
usa
i am going to tile the kitchen at the weeknd how do i mark out on the floor to check if it is square?? I know that if i mark 2 lines to find the centre of the room but that wont mean I am tiling squarely -if thats a word - any help would be appreciated:thumbsup:
Hello all,
I have a victorian mosaic tiled floor in my hallway, but recently had some work done elsewhere in the house and the builders managed to break three of the edge tiles... I have been searching for months to try and find replacements so that I can fix the damage, but it seems that the...
scgough
Thread
edwardian
edwardian floor
geometric
help
square
thick
usa
victorian
victorian floor
victorian floor tiling
Could any body give me a rough guide what price is charged for putting up 5 square meters of 10cm porcelain wall tiles in a kitchen please?
Price per square meter or full job.
The walls have been skimmed but not yet etched or unibonded.
Cheers!
Mark.
Morning all,
I've had my TS40+ just over 12months now but since before Xmas it's started cutting off by about 3 or 4mm:mad2:
Never had this problem with my old bog standard TS's:prrr:
I contacted Rubi when it first started happening - waste of time:thumbsdown:
Anyone got any ideas on...
I've done plenty of round-edged chrome trims around windows, but today or possibly tomorrow I'll be making my debut with Squared edged chrome trim...
Just wondering, if folk tend to still mitre the corners???
I'm a bit 50/50 'cos I reckon it might look better with them just butted up to...
Some of you may have seen the workprogress of my ocean wave, which I have now decided I would like to keep freestanding to be a centre piece in a future exhibition.
Now I am triyng to think what board would be best to fix it on, of 2 meter square size, that would be possible to cut into a wave...
Hi guys - any advice or suggestions welcomed!
I have been a keen DIY tler for about 10 years and a couple of months ago took the plunge to start doing kitchen and bathroom work for people other than friends and family.
Lo and behold, first time I have started working with porcelain, all is...
Hi all, my first post.
On Monday bought a new TX 700, fantastic bit of kit, but have noticed that it is cutting out of square with the guide set at 0 degrees. We are talking 2mm out on a 600mm tile.
First noticed as the scribing wheel does not run parallel with the breaking bar on the base...
I am proposing to lay 600x600 polished porcelain floor tiles, they have square edges as opposed to normal floor tiles with slightly bevelled/rounded edges, what is the best width of spacer & grout to use, I usually use a flexi rubber grout float is this o.k
thanks in advance
Hi all
Out of interest came across some Homelux chrome square edge metal tile trim.
Has anybody used these and what were there thoughts?
Reason for asking i've got a 12mm tile job soon and the 12.5mm tile trims don't seem to but up comfortably.
With these square edged not only did the tile fit...
i have just discovered the little square under our name when we post.Have a look and see what it says about you when you put the cursor on it!let us all know.:thumbsup:
This week I have been renovating a bathroom for a couple who got a bad tiling job done on their bathroom by some cowboy. After 4 years the lady of the house can't look at it any longer so its a complete stripout and redo.
I felt sorry for them and was determined that everything would be spot on...
Due to bathroom not being square, both the ends of the bath don't fit flush to the wall, although it fits flush on the long side thankfully.
I am going to tank with wetdec's tanking kit (already purchased) but can you please tell me how to bridge these gaps please? The maximum gap size before...
hey guys. just looking for your advice on the best possible way of squaring a floor.
my first floor is about 17m² and would like to know how you guys get it right!!
thanks.
Hi,
My 'professional' tiler can not do a 3 way joint - I have seen 9mm 3 way corners that will stop the need for 45 degree angles and will look much nicer than the piles of grout i currently have with sharp jutting out corners.
Does anyone know where I can get 8mm bright silver 3 way...