Recent content by bolts

  1. B

    Has my Tiler done a good Job ?

    looking at the first picture I would never have said they were 600 x 600 but oddly, looking at the second pic they could be square. still looks good to me either way if no specific instructions were given.
  2. B

    Uneven floorboards. Will tiles come loose?

    I ripped up the old boards and re-boarded with ply. Then over-boarded with cement board and as been said you can use an offset toilet waste, which I did. In this case I had to pull up some of the floorboards anyway, and also found that some parts of the floor weren’t supported properly. I also...
  3. B

    Uneven floorboards. Will tiles come loose?

    If it was me I’d re-board the floor first, then overboard with NMP as per the instructions with NMP glue and screws. Last bathroom I did was just like this but maybe not quite as level. As it happens I needed the floor up anyway to access the pipework so it just made sense to replace it.
  4. B

    Orbry board

    First time I’ve used Orbry board and seems a good product and reasonably priced. One quick question, when using it with the orbry self adhesive joint tape do you need to paint tanking membrane over the tape? The instructions just say tape the joints to make it waterproof. This is for a shower...
  5. B

    Loose Floor tiles :( New Floor

    No NMP isn't shiny, must be something else.
  6. B

    Is this a bad tiling job ? what can i do ?

    Maybe the tiling was done by the same guy that plastered and painted the walls above it :) looks to be pretty much the same standard of work.
  7. B

    Shower Tray Riser kit install

    Yes I was thinking that battens would be a good idea as they will hold it much better that just sticking the feet to the floor. I will use battens to hold it in place and the feet to just support the weight across the rest of the tray.
  8. B

    Advice on bathroom shower backer board and waterproofing installation

    in responce to : 1. Should I waterproof the marine ply? I'm not sure if you mean the whole floor or just below the shower tray ? If correctly fitted and sealed the area below the shower tray should be the dryest part of the room. The only place you could then have an issue with is the shower...
  9. B

    Shower Tray Riser kit install

    Hi Yes it is supplied by the manufacturer and I have followed the instructions. The instructions didn't say anything about attaching to the floor. Which is why I asked for suggestions. All looks good though. The base was marked with the position to fix the pads so in this case they must be...
  10. B

    Shower Tray Riser kit install

    Thanks guys, I'll go with the sticky pads and a bit of quick set under the feet. Yes I was thinking a wooden frame might be an option but seems ok so I'll go with it.
  11. B

    Shower Tray Riser kit install

    Hi, I am doing an en-suite at the moment and will need to install the shower tray which comes with a riser kit. Now normally these things are much like bath feet and have holes in to screw them into the base of the shower tray (or wooden support)and screw the bottom of the feet to the floor...
  12. B

    Self Employed after Tiling Course

    So did you do the course? and almost a year later how are you progressing ?
  13. B

    new tiler / help needed in wet cutter choice

    No, Mine is the bench saw.
  14. B

    new tiler / help needed in wet cutter choice

    I have a vitrex pro tile too, does the job and picked it up second hand for £110.00 so a bargain really, it had only been used for one job. there's a ruby DU-200 on Gumtree now for £110.00 in portsmouth or a Vitrex in Walsall area for £100 No idea what part of the country you are in but hope it...
See more

Featured Threads

Advertisement

Tilers Forums UK | UK Tiling Forum
https://uktilingforum.co.uk | UK Tiling Forum
Back