Trying to learn from my mistakes here......

[cornish_crofter]

A few issues have come up with this wetroom.

One or two have been caused by me not being thorough enough with my preperation etc. Others have probably been caused by lack of experience or technique.

The former went down fine. Absolutely level etc.

However, a couple of areas caught me out

1) I had done most of the screed but had left channels for the plumbing. Now unfortunately when I back filled these I might have been too high in a few places. My view is that if I can't get it dead level with the existing screed for whatever reason, I should have aimed for it to be a bit lower than the existing floor. That way I would be left with the task of building up with a bit of adhesive, rather than having to remove screed.

2) Ditra Matting - where do I start! Firstly I thought I'd managed to get the ditra matting on level or straight with the floor. I used a mosaic trowel to apply the adhesive and the back of the same trowel to flatten it out. I even checked it with a level FFS! It looked to be level with the floor (slight fall in floor). The biggest problems I have had have been where I've got the Kerdi tape (or the Wetdecs supplied equivilent) laid on top. Despite having used the back of the trowel to flatten it (or a spatula where I couldn't get in with the trowel) I've still got lumps underneath!!!!!

3) Ditra matting again. The original screed that I put down was level with the top of the former. In fact when the former went down it lined up beautifully with the top. I had allowed exactly 50mm depth for the former. I then applied a bed of adhesive using my 10mm round notched trowel on both the former and the floor. Unfortunately the ditra matting added 3mm :mad2:. Now I should have taken that into account and laid the screed 3mm lower, but I didn't. So I think I know where I went wrong there.

4) Applying the adhesive for the floor tiles. Now, fortunately for me the tiles I've got are thinner than allowed for. Hence most of the lumps in the tape are not an issue as the extra adhesive copes with them. However, applying the adhesive is really slowing me down!

Essentially I'm either putting on not enough and there is poor contact, or I'm putting on too much and it's oozing out of the bloody joints!:mad2::mad2::mad2::mad2::mad2:

I would really appreciate help with laying the ditra matting and tape, and applying the adhesive. I'm looking at about a 3mm bed after the tile is in position. As I've explained the ditra matting isn't perfectly level, mainly thanks to my kak handidness as explained above. I've only got 4 more tiles to lay but at the rate I'm going it'll take me all morning to lay the bloody things!

Either I get it cracked or I'm giving up tiling altogether! that is how I feel.

And any help with levelling the walls out would be good. I've given myself the same problems where the tape meets the walls as I couldn't get those flat either!

 

[kilty55]

hello cornish,if your floors out cant you back butter as well to ensure good coverage,a wetroom imo is a difficult thing to do ,i dont have much experience of them myself apart from a few floors ive done in them to be honest.

take a deep breath and have a beer mate,

 

[Dan]

It's not an area I'm brilliant in so I'll let the lads answer the actual questions. However you learn like this and this is what experience actually is. Don't hang up the tools as on your next job like this you'll be very prepared.

 

[cornish_crofter]

The problem I'm having at the moment is working out exactly how much adhesive to apply to where the tile is going.

Yesterday I laid most of the tiles on the floor but every single tile was a complete guess and re apply.

I'm using the 10mm round notched trowel and started off by pressing down onto the substrate, but when this isn't giving enough of a bed I find I'm applying again but leaving the tips about 1 to 2mm off the substrait. It seems to be a very fine line between not enough so you've not got 100% contact to too much so it's going everywhere.

On a different note, there is one tile I just can't get level, thanks to that bloody Ditra matting with tape over it in that spot.. I've got it as best I can and left it. It happens to be where the floor meets the former, so I should be able to lose most of the problem in the grout. I don't think it looks too bad although I know it's there. My betting is that the customer will never notice it.

 

[tfs]

It sounds to me that you may have some bubbles/ adhesive build up under the mat (just a possibilty) did you flaten out the mat?

I would reccomend a 400mm by 200mm peice of 18mm ply with carpet stuck round it with spray, then use this to push out any voids/ air between mat and floor (same way you do when wall papering.

 

[cornish_crofter]

The problem with the ditra matting is mainly around the corners where the tape (6inch strip stuck down with tile adhesive) is stuck onto it. It seems that it's just not flat in these areas.

The floor is not too much of a problem apart from 1 tile, where I think I may have managed to lose the visual impact of it not sitting quite level with the one next to it. I am blessed with the tiles not being as thick as I had thought they were so there is room to accomodate this with the floor.

The walls are my concern. The walls around the bathroom aren't bad, but I've not helped myself where the tape is stuck on the walls. The problem is where two pieces overlap each other.

I don't think I've got air trapped underneath. Apart from the problem with the tape, I suspect I have simply made the mistake of not pushing in the trowel into the edges of the room

I think that next time I do a wetroom I'll actually remove the top layer of plaster from 3 to 4 inches up from the floor to give myself room for the tape and adhesive to sit.

 

[tfs]

ahh, the internal corner between floor and wall?

 

[charlie1]

You need to find out where the "high point" in you floor is and start there!, you can add material but you cant really take away

 

[cornish_crofter]

You need to find out where the "high point" in you floor is and start there!, you can add material but you cant really take away

I've pretty much sorted the floor now, just 4 more tiles to go - trimmed ones near the door.

The problem I've got is not having the skill in applying just the right amount of adhesive. Ideally I would like to lay these tiles in about half an hour without either not having enough contact or having the tile adhesive ooze out of the joints.

The question for tomorrow is how do you do this?

Your logic will be applied to the walls though.

 

[charlie1]

Whats the rush?? as for adhesive oozing out, mix it slightly thicker and this should avoid that one!!